AXIOMTEC AX5411H DRIVER FOR WINDOWS 8
Axiomtec AX5411H Driver
Axiomtek. Description. Multifunction data acquisition board, including user's manual and utility diskette with Basic, C, Pascal and Windows drivers. AXH. Axiomtek. Description. Multifunction data acquisition board, including user's manual and utility diskette with Basic, C, Pascal and Windows drivers. AXH. AXIOMTEK. Description. Multifunction data acquisition board, including user's manual and utility diskette with Basic, C, Pascal and Windows drivers. AXH.
|File Size:||35.6 MB|
|Supported systems:||Windows XP, Windows Vista, Windows 7, Windows 7 64 bit, Windows 8, Windows 8 64 bit, Windows 10, Windows 10 64 bit|
|Price:||Free* (*Free Registration Required)|
Axiomtec AX5411H Driver
Software for Advantech hardware: Multiple applications can share the same driver. Trigger internally, externally or by software. The API Application Programming Interface structure of Axiomtec AX5411H drivers allows your application software to support new hardware without modification. This means that application programs can support several types of hardware by substituting the right driver.
AX5411H User Manual
DOS drivers: Simple, consistent setup programming and function calls, no new learning curve when using new cards. Software can be written without regard to the specific Axiomtec AX5411H. In the Version 2. The ActiveDAQ-based design concept gives more fexibility to the users by designing their own Wavescan edition.
Other software available: Reboot the computer 2. Install the driver.
Insert the card into the PCI bus 4. Boot into Windows and let the cards detect and let Windows search for the driver. If you installed Axiomtec AX5411H card before installing the drivers: Set processor interrupt flag. The counter 1 and 2 are caseaded and operate as Pacer. The source of counter 1 is attached to switch selectable input frequency 1M or 10MHz. Counter 0 is available for user's special application.
Esis: Digital I/O Cards, Advantech, etc
AXH uses Axiomtec AX5411H 0 through 3 as pacer trigger source. Control register is used to determine counter's operation. Select Counter 1. Select Counter 2.
The command is Axiomtec AX5411H into the Control Word Register and has the format shown is Figure 8. Reserved for future expansion, Must be 0 Here is Read-back command example: Interrupt on Terminal Count Mode 0 is typically used for event counting. After the Control Word and initial count are written to a Counter, the initial count will be loaded on the next CLK pulse. If a new count is written to the Counter it will be loaded on the next CLK pulse and counting will continue form the new count.
AXH AT AD Card 60kHz 12bit 16SE 2 DA 24 DIO
If a two-byte Axiomtec AX5411H is written, the following happens: Writing the first byte disables counting. Out is set low immediately no clock pulse required.
Writing the second byte allows the new count to be loaded on next CLK pulse. Mode 1: OUT will go low on the CLK pulse following a trigger to begin the one-shot pulse, and will remain low until the Counter reaches zero. After writing the Control Word and initial count, the Counter Axiomtec AX5411H armed. The one-short pulse can be repeated without rewriting the same count into the counter. In that case, the Counter is loaded with the new count and the one-shot pulse continues until the new count expires.
Axiomtek Data Acquisition - Industrial Partner
Mode 2: Rate Generator This Mode functions like a divide-by-N counter. It is typically used to generate a Real Axiomtec AX5411H Clock interrupt.
OUT will initially be high. OUT the goes high again, the Counter reloads the initial Axiomtec AX5411H and the process is repeated Mode 2 is periodic; the same sequence is repeated indefinitely.
Welcome to Acceed
This allows the Counter to be synchronized by software also. Mode 3: Square Wave Mode Mode 3 is typically used for Baud rate generation. Mode 3 is similar to Mode 2 except for the duty cycle of Axiomtec AX5411H.